Aube-technologies TH114 Manuel d'utilisateur télécharger pdf

TH114

User s Guide

Non-programmable Thermostat

TH114

400-114-000-B 21/2/05 1/2

Aube’s TH114 Series non-programmable thermostats can be used

to control ambient or floor temperature. The following models are

available:

Each thermostat consists of a control module which must be

mounted on a PB112 Series power base. For the selection and

installation of the power base, refer to its installation instructions.

The DIP switches are located at

the back of the control module.

2.1 Temperature Display (S1)

To switch between °C and °F.

2.2 Model (S2)

Note: Available on certain models only

n Refer to the installation instructions of the

power base.

o Insert the tabs at the top of the control

module in the slots at the top of the

power base.

p Secure the control module using the cap-

tive screw underneath the base.

Note: Do not obstruct the thermostat's vents.

As soon as the thermostat is powered, it undergoes a

series of tests before displaying the actual tempera-

ture.

The measured temperature is below 0°C (32°F). Heat-

ing is turned On.

The measured temperature is above 50°C (122°F) (A

or AF model) or 60°C (140°F) (F model).

The floor sensor is defective or not properly connected

(F model only), or the thermostat is defective.

Note: This procedure must be performed if the thermostat is

mounted on a GFCI-equipped power base.

Test the GFCI immediately after installing

the control module, and once a month there-

after.

n Raise the temperature until the heat-

ing power indicator appears.

o Press the Test button.

p If the test is successful, you will hear a

click caused by the GFCI relay tripping.

The heating power indicator will disap-

pear, GFI will appear and the Fault light

will illuminate. Reset the thermostat by

switching it to Standby and back to On.

q If the test has failed, cut power to the heating system from the

main electrical panel and call customer service.

Note: If the Fault light is On during normal operation, cut power to

heating system at the main electrical panel and have an electrician

verify the installation.

1. Description

A model: controls and displays the ambient temperature

F model: controls and displays the floor temperature

uses an external temperature sensor

AF model: controls and displays the ambient temperature

maintains the floor temperature within desired

limits

uses an external temperature sensor

2. DIP Switch Configuration

F: To select the F model

AF: To select the A or AF model

1 to 24%

25 to 49%

50 to 74%

75 to 99%

100%

GFCI test button * /

Backlight button *

Temperature

adjustment button

On/Standby button

Power output

Actual or setpoint

temperature

Arrow appears

when the setpoint

is displayed

GFCI fault indicator *

GFCI fault light *

* available on certain models only

3. Installation

4. Power-up

5. Error Messages

6. GFCI Test

1 2 3

Résumé du contenu

Page 1 - User s Guide

TH114User s GuideNon-programmable ThermostatTH114 400-114-000-B 21/2/05 1/2Aube’s TH114 Series non-program

Page 2 - 7.1 Backlight

TH114 400-114-000-B 21/2/05 2/27.1 BacklightWhen either of the buttons is pressed, the display is lit for

Page 3 - Installation Instructions

PB112-024T 400-112-000-B 18/1/06 1/1The PB112-024T power base can be used on any TH11x seriesthermostat (w

Plus de documents pour Panneau de contrôle Aube Technologies TH114

Voir le document Aube-technologies TH114 Manuel d'utilisateur

Aube-technologies TH114 Manuel d'utilisateur (1 pages)

Commentaires sur ces manuels

Pas de commentaire

Aube-technologies TH114 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Panneau de contrôle Aube-technologies TH114. Aube Technologies TH114 User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Panneau de contrôle Aube Technologies TH114

Commentaires sur ces manuels

Produits connexes et manuels pour Panneau de contrôle Aube-technologies TH114